Top 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Do not take too lightly the forklift at the workplace. If the procedure is not good, there will certainly be significant crashes in mins, and there are numerous crashes entailing forklifts.

Situation 1: The forklift cargo blocked the motorist's sight, and the individual in front can not be located, causing a moving crash.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees used their body weight as the counterweight, which almost caused casualties.
Case 3: The size of the forklift cargo goes beyond the permitted width of the route and hangs on the roadside shelf, which virtually causes an accident.
Case 4: Forklift is speeding up and surrender throughout a turn.
Situation 5: The forklift motorist did not discover the pedestrian, and the pedestrian did not notice the forklift.
Case 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not use the seat belt, the forklift lifter drops and the chauffeur is crushed when the forklift rolls over.
Instance 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift operation should pay attention to these issues ：.

Beginning.
1. Prior to starting, observe the surroundings, and after validating that there are no challenges that hinder the security of driving, honk the horn first and after that start.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge should be risk-free before beginning.
3. When the forklift begins with a tons, the driver needs to initially confirm that the tons is steady and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the mast needs to be tilted in reverse. .
2. Do not raise the fork too high when driving. When going into and leaving the work website or while driving, take care that there will be no challenges overhead. When the tons is taking a trip, the fork needs to not be increased too expensive, which will certainly influence the security of the forklift. .
3. After dumping, the fork ought to be decreased to the typical driving position prior to driving. .
4. When transforming, if there are pedestrians or cars close by, the driving signal should be issued initially. High-speed sharp turns are prohibited. High-speed doglegs will certainly cause the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to turn off the flame and slide, and it is restricted to brake all of a sudden while driving with lots unless there are special circumstances.
6. When the forklift is running, it has to obey the web traffic rules in the factory and have to maintain a specific safety and security range from the car ahead. .
7. When the forklift is running, the tons has to remain in the lowest setting that does not impede the driving, and the gantry needs to be correctly tilted back. The load shall not be elevated other than when piling or filling. .
8. The height of the load have to not block the driver's view. In unique conditions, when the item impacts the forward vision, drive at a reduced rate when turning around.
9. It is restricted to turn on the ramp, nor to drive across the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a reduced rate when entering the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is forbidden for personnel to base on the fork to hold items and play a stabilizing duty. .
12. If problems are found, they will certainly be fixed and reported in a prompt way, and they will never ever operate with illnesses or conceal them.

loading and unloading.
1. When fork-loading items, the range between the two forks must be readjusted as required to make the tons of both forks balanced and not manipulated, and one side of the product ought to be against the rack. .
2. It is forbidden to work with a solitary fork or utilize a fork top or pull. In special scenarios, security warning signs should be established to advise bordering pedestrians. .
3. In the process of loading and unloading products, the forklift should be braked with the brake. .
4. The rate of the car should be sluggish and steady. Take care not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as possible under the load, and it ought to be noted that the fork idea ought to not touch other items or objects. The lots ought to be maintained with marginal back tilt of the gantry to make sure that the lots does not slide in reverse. The mast can be slanted onward somewhat when the lots is decreased to enable easy positioning of the load and removal of the forks. .
6. It is restricted to fork goods at broadband and ram hard objects with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to stay clear of the collapse of the goods and injure people. .
8. Overwhelming is forbidden, and it is prohibited to use forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Pull the parking brake deal with Stand-on Electric Pallet Stacker to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be checked, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, examine whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leak ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across somebody before you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free switching";.
6. Running up and down the incline must be slow and consistent, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the gradient is greater than 10%, the automobile ought to be driven in reverse when declining;.
8. Electric Forklift Truck for Warehouse When the forklift employees bring the goods and move on, if they experience huge or hefty products and go to the vehicle driver's line of sight, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844